Alpha AIR-658 Instrukcja Obsługi

Przeglądaj online lub pobierz Instrukcja Obsługi dla Szlifierki elektryczne Alpha AIR-658. Alpha AIR-658 Instruction manual Instrukcja obsługi

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj
  • Strona
    / 16
  • Spis treści
  • BOOKMARKI
  • Oceniono. / 5. Na podstawie oceny klientów
Przeglądanie stron 0
www.nsisolutions.com Manual Rev J3
SEAM PHANTOM
INSTRUCTION MANUAL
Model No. 0010-1
Please read this instruction manual thoroughly to ensure safety and correct use of tool.
Keep this manual in a place where operators can access it easily, anytime when necessary.
PATENT Number: US 8,162,726
MADE IN USA
Przeglądanie stron 0
1 2 3 4 5 6 ... 15 16

Podsumowanie treści

Strona 1 - SEAM PHANTOM™

www.nsisolutions.com Manual Rev J3 SEAM PHANTOM™ INSTRUCTION MANUAL Model No. 0010-1 Please read this instruction manual thoroughly to ensure

Strona 2 - TABLE OF CONTENTS

Page 10 Adjusting the Seam Phantom To ensure the tightest possible seams, each Seam Phantom is checked for squareness before it leaves the facto

Strona 3 - GENERAL SAFETY RULES

Page 11 USE INSTRUCTIONS Before Using the Seam Phantom - Preparations Before using the assembled Seam Phantom, be sure to complete the following

Strona 4 - to Grinder

Page 12 How To Operate NOTE: If you have access to the Internet, see www.seamphantom.com for an instructional video as well as pictures of the p

Strona 5

Page 13 3. Back Grind or “Undercut” The back grinding is done using the Phantom SL3™ 2" cup wheel. Ensure adequate water flow is provided b

Strona 6

Page 14 CLEANING AND MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection

Strona 7

Page 15 FIGURE 10 – Cleaning (Electric version shown) 3. Air Tool Perform regular oiling and other maintenance of the air polisher as recomme

Strona 8 - Assembly Exploded View, Air

Page 16 CONTACT NSI SOLUTIONS Whether it’s for replacement parts, technical or usage support, or just to brag about how tight your seams are, fee

Strona 9 - Air Polisher Adapter

Page 2 INTRODUCTION Thank you for purchasing the NSI Solutions SEAM PHANTOM®. Please read this instruction manual thoroughly for assembly instruc

Strona 10 - Adjusting the Seam Phantom

Page 3 GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in elect

Strona 11 - USE INSTRUCTIONS

Page 4 Tools Needed For Assy Of Seam Phantom® to Grinder Electrical Version 3 mm Allen (Hex) Wrench Alcohol (rubbing) to prepare electric grinder

Strona 12 - FIGURE 9 – Gauge Block Use

Page 5 FIGURE 2 – Assembly Exploded View, Electric (Spray Skirt not shown) 3. Position Seam Phantom and Splash Guard Angle, and attach to Gri

Strona 13

Page 6 4. Install Spray Skirt a) Clean grinder with denatured (rubbing) alcohol prior to installing skirt b) Mark the center of the skirt alon

Strona 14 - CLEANING AND MAINTENANCE

Page 7 5. If desired, fasten water supply hose to cord of Grinder using electrical tape or other suitable method. 6. Install arbor spacer (see

Strona 15

Page 8 Assembly Instructions – Air Version 1. Attach the arbor extension to the polisher and tighten appropriately. See Figure 7. FIGURE 7 –

Strona 16 - CONTACT NSI SOLUTIONS

Page 9 FIGURE 8 – Air Polisher Adapter 3. Attach the polisher, adapter and arbor extension to the rest of the Seam Phantom using (4) 4mm X 22

Komentarze do niniejszej Instrukcji

Brak uwag